Linksys SPA2102 ATA admin tone codes


The Linksys / Cisco SPA2102 2FXS VoIP Phone Adapter
is a compact two line VOIP ATA (Analog Telephone Adapter) with built in router. With this little box, a VOIP service provider and a decent internet connection you can get rid of your phone service and pay pennies to make calls anywhere in North America as well as getting more control over your phone numbers.
[GARD]
This ATA router features both a web server admin page and a voice prompt admin gateway. This means that if you can’t get access to the web admin you can use your telephone handset to setup and maintain this little device. The tricky bit is that you need to know what touch tone codes are used to control what settings. For future reference I post those codes below:

ActionKey CodeOptionsNotes
ActionKey CodeOptionsNotes
Enter Interactive Voice Response Menu.****Use this command (four stars) to enter the Interactive Voice Response Menu. Do not press any other keys until you hear, “Linksys configuration menu. Please enter the option followed by the # (pound) key or hang up to exit.”
Check net connection type100# Hear the Internet connection type of the Phone Adapte
Check internet IP address110#Hear the IP address assigned to the Phone Adapter’s Internet (external) interface.
Check Network Mask or Subnet Mask120#Hear the network or subnet mask assigned to the Phone Adapter.
Check Gateway IP address130#Hear the IP address of the Phone Adapter (usually the network router).
Check MAC Address140#Hear the MAC address of the Phone Adapter in hexadecimal string format.
Check Firmware Version150#Hear the current version number of firmware running on the adapter.
Check Primary DNS server IP address160#Hear the IP address of the primary DNS server
Check web server port170#Hear the port number of the internet web server used for the web based utility
Check local IP address210#Hear the local IP address of the phone adapter.
Set internet connection type101# Press 0 to use DHCP. Press 1 to use a static IP address. Press 2 to use PPPoESelect the type of Internet connection you are using. Refer to the documentation supplied by your Internet Service Provider (ISP).
set static IP address111#Enter the IP address using numbers on the telephone keypad. Use the * (star) key when entering a decimal point.First, set the Internet Connection Type to static IP address; otherwise, you will hear, “Invalid Option,” if you try to set the static IP address.
Set Network (or Subnet) Mask121#Enter the network or subnet mask using numbers on the telephone keypad. Use the * (star) key when entering a decimal point.First, set the Internet Connection Type to static IP address; otherwise, you will hear, “Invalid Option,” if you try to set the network or subnet mask
Set Gateway IP Addres161#Enter the IP address using numbers on the telephone keypad. Use the * (star) key when entering a decimal point.First, set the Internet Connection Type to static IP address; otherwise, you will hear, “Invalid Option,” if you try to set the IP address of the primary DNS server.
Set the Mode201#Press 0 to select the router/NAT mode. Press 1 to select the bridge/switch mode.If the Phone Adapter acts as the router for your network, use the router/NAT mode. If your network already has a router, use the bridge/switch mode.
Enable/Disable WAN Access to the Web-based Utility7932# Press 1 to enable. Press 0 to disable Use this setting to enable or disable WAN access to the Web-based Utility. (This Utility lets you configure the Phone Adapter.
Manual Reboot732668 After you hear, “Option successful,” hang up the phone. The Phone Adapter will automatically reboot
Factory Reset73738 Press 1 to confirm. Press * (star) to cancel. If necessary, enter the password. The Phone Adapter will request confirmation; enter 1 to confirm. You will hear, “Option successful.” Hang up the phone. The Phone Adapter will reboot, and all settings will be reset to their factory default settings
User Factory Reset877778Press 1 to confirm. Press * (star) to cancel. The Phone Adapter will request confirmation; enter 1 to confirm. You will hear, “Option successful.” Hang up the phone. The Phone Adapter will reboot and all user-configurable settings will be reset to their factory default settings